Drill holders for dowel drills
In a dowel drilling machine or drilling unit, a dowel drill is not mounted directly in the spindle: the connection is made via a drill holder for dowel drills. This category includes drill holders in left- and right-hand versions, available as a flat base version, with a centering seat of 11 × 4 mm or with a centering cone in various angles, including 20°48' and 30°.
The direction of rotation is the most important selection criterion. Drilling groups drive their spindles alternately counterclockwise and clockwise, which means both versions are needed as a pair. Then choose the correct mount for your dowel drills — a seat or cone — and check this combination carefully. A drill that does not fit fully into the correct seat will run out of true. In dowel joints, even a small deviation immediately leads to joints that do not fit properly.
Filters
B (bore) in mm
L (total length) in mm
S (shank) special
S1 (shank diameter 1)
Markings (connection)
d (small diameter) in mm
D (diameter) in mm
Rotation direction

Drill holder, right hand D=19,5mm S=M8 B=10mm
- RH (right-hand rotation)


Drill holder, right hand D=16mm S=M8 B=8mm
- RH (right-hand rotation)


Drill holder, right hand D=19,5mm S=M10 B=10mm · 302.000.01
- D=19,5mm M10
- RH (right-hand)

Drill holder, left D=19,5mm S=M10 B=10mm · 302.000.02
- D=19,5mm M10
- LH (left-hand rotation)

Drill holder, right hand D=16mm S=M10 B=8mm
- D=16mm M10
- RH (right-hand rotating)

Drill holder, left D=16mm S=M10 B=8mm
- D=16mm M10
- LH (left-hand rotation)

Drill holder with centering cone 30°, right D=19,5mm B=10mm
- D=19,5mm M10
- RH (right-hand)

Drill holder with centering cone 30°, left-hand D=19,5mm B=10mm
- D=19,5mm M10
- LH (left-hand rotation)

Drill holder with centering cone 30°, right D=16mm B=8mm
- D=16mm M10
- RH (right-hand rotating)

Drill holder with centering cone 30°, left-hand D=16mm B=8mm
- D=16mm M10
- LH (left-hand rotation)

Boring head with centering cone 20° 48', right-hand D=19,5mm B=10mm
- D=19,5mm S=M8
- RH (right-hand rotation)

Drill holder with centering cone 20° 48', left D=19,5mm B=10mm
- D=19,5mm S=M8
- LH (left-hand)

Drill holder with centering pin 11x4 mm, right · 305.000.01
- D=19,5mm M10
- RH (right-hand)

Drill holder with centering 11x4 mm, left · 305.000.02
- D=19,5mm M10
- LH (left-hand rotation)

Drill holder with centering pin 11x4 mm, right · 305.080.01
- D=16mm M10
- RH (right-hand rotating)

Drill holder with centering 11x4 mm, left · 305.080.02
- D=16mm M10
- LH (left-hand rotation)

Bore holder with center point 9x4 mm, right-hand · 358.000.01
- D=19.5mm
- LT=40mm
- S=M8

Drill holder with centring 9x4 mm, left · 358.000.02
- D=19,5mm
- LT=40mm
- S=M8

Drill holder, right hand D=19,5mm S=M10 B=10mm · 359.000.01
- LT=46mm
- RH (right-hand rotation)

Drill holder, left D=19,5mm S=M10 B=10mm · 359.000.02
- LT=46mm
- LH (left-hand)

Quick-change drill chuck for Biesse, right D=15mm B=10mm
- D=15mm d=2mm
- LT=37mm
- RH (right-hand rotation)

Quick-change drill chuck for Biesse, left D=15mm B=10mm
- D=15mm d=2mm
- LT=37mm
- LH (left-hand)
24 of 28 products shown