Bushing enlargers
When the bore of a tool or ball bearing is too small for the desired clamping setup, a bushing enlarger offers a practical solution. Where a reducer ring reduces an oversized bore, a bushing enlarger increases the effective clamping diameter. This allows a router spindle or ball bearing to fit the correct shaft or the desired holder. The range includes bushing enlargers for cutters and ball bearings.
As with any shaft connection, the bushing must fit completely free of play. Any play causes imbalance in the rotating tool. Always fit the bushing enlarger clean and grease-free, and after clamping check that everything rotates freely and without wobble before letting the machine run at full speed. Before placing your order, measure both diameters carefully with a caliper.
Filters
B (bore) in mm
D (diameter) in mm
L (total length) in mm
d (small diameter) in mm

Sleeve enlarger for shank D=12,7mm B=9,5mm L=25mm
- D=12,7 d=9,5mm

Oversized bush for ball bearing D=12,7mm L=7,5mm d=4,76mm
- D2=12,7 D3=4,76mm

Oversized bush for ball bearing D=8mm L=6,5mm d=4,76mm
- D2=8 D3=4,76mm

Oversized bush for ball bearing D=6,35mm L=6,8mm d=4,76mm
- D2=6,35 D3=4,76mm


Sleeve enlarger for shank D=8mm B=6,35mm L=25mm
- D=8 d=6,35mm

Sleeve enlarger for shank D=12mm B=10mm L=25mm
- D=12 d=10mm

Sleeve enlarger for shank D=16mm B=13mm L=45mm
- D=16 d=13mm

Sleeve enlarger for shank D=9,5mm B=6mm L=25mm
- D=9,5 d=6mm

Sleeve enlarger for shank D=9,5mm B=6,35mm L=25mm
- D=9,5 d=6,35mm

Sleeve enlarger for shank D=9,5mm B=8mm L=25mm
- D=9,5 d=8mm


Sleeve enlarger for shank D=12,7mm B=6,35mm L=25mm
- D=12,7 d=6,35mm



Sleeve enlarger for shank D=12,7mm B=8mm L=25mm
- D=12,7 d=8mm

Oversized bush for ball bearing D=19,05mm L=12mm d=12,7mm
- D=12 d=8mm
- L=25mm

Oversized bush for ball bearing D=50,8mm L=12mm d=12,7mm
- D=19,05 d=12,7mm
Reducing sleeves for router shanks and ball bearings
A reducing sleeve adapts a smaller diameter to a larger size. In this category you will find CMT reducing sleeves in two types: sleeves for the shank, which you slide over the shank of a router bit so it fits a larger collet, and sleeves for ball bearings, which let you mount a bearing with a larger bore on a thinner axle. The inside diameters range from 4,76 to 13 mm; the outside diameters match common collet sizes such as 8, 9,5, 12 and 12,7 mm.
Reducing sleeve for the shank: choose based on shank and collet
The inner diameter of the sleeve must be exactly the same as the shank of your router bit, the outer diameter the same as the size of your collet. This allows a router bit with a shank of 6, 6,35 or 8 mm to still fit in a larger collet. The shank sleeves are usually 25 mm long: slide the sleeve fully over the shank and clamp sleeve and shank together as deeply as possible in the collet, without letting the shank rest on the bottom. If there is a suitable collet for your shank, that remains the preferred option; see the collet holders.
Reducing sleeve for ball bearings
With routers fitted with a guide bearing, you can use a reducing sleeve to mount a ball bearing with a larger bore on the router's axle, for example on an axle of 4,76 mm (3/16 inch). This lets you use a bearing with a different outside diameter with the same router and changes the cutting depth. Fit sleeve and bearing cleanly and without play, tighten the assembly securely and check by hand that the bearing turns freely. Loose ball bearings can be found in the corresponding category.