Cutting tools: choice of 20,000 articles
Select language

Bushing enlargers

When the bore of a tool or ball bearing is too small for the desired clamping setup, a bushing enlarger offers a practical solution. Where a reducer ring reduces an oversized bore, a bushing enlarger increases the effective clamping diameter. This allows a router spindle or ball bearing to fit the correct shaft or the desired holder. The range includes bushing enlargers for cutters and ball bearings.

As with any shaft connection, the bushing must fit completely free of play. Any play causes imbalance in the rotating tool. Always fit the bushing enlarger clean and grease-free, and after clamping check that everything rotates freely and without wobble before letting the machine run at full speed. Before placing your order, measure both diameters carefully with a caliper.

Read more about this category
Sleeve enlarger for shank D=12,7mm B=9,5mm L=25mm

Sleeve enlarger for shank D=12,7mm B=9,5mm L=25mm

  • D=12,7 d=9,5mm
€14.20
€17.18 VAT incl.
Code:799.001.00
In stock
Oversized bush for ball bearing D=12,7mm L=7,5mm d=4,76mm

Oversized bush for ball bearing D=12,7mm L=7,5mm d=4,76mm

  • D2=12,7 D3=4,76mm
€7.20
€8.71 VAT incl.
Code:799.014.00
In stock
Oversized bush for ball bearing D=8mm L=6,5mm d=4,76mm

Oversized bush for ball bearing D=8mm L=6,5mm d=4,76mm

  • D2=8 D3=4,76mm
€7.20
€8.71 VAT incl.
Code:799.017.00
In stock
Oversized bush for ball bearing D=6,35mm L=6,8mm d=4,76mm

Oversized bush for ball bearing D=6,35mm L=6,8mm d=4,76mm

  • D2=6,35 D3=4,76mm
€7.20
€8.71 VAT incl.
Code:799.019.00
In stock
Sleeve enlarger for shank D=8mm B=6mm L=25mm

Sleeve enlarger for shank D=8mm B=6mm L=25mm

  • D=8 d=6mm
€9.30
€11.25 VAT incl.
Code:799.060.00
In stock
Sleeve enlarger for shank D=8mm B=6,35mm L=25mm

Sleeve enlarger for shank D=8mm B=6,35mm L=25mm

  • D=8 d=6,35mm
€9.30
€11.25 VAT incl.
Code:799.064.00
In stock
Sleeve enlarger for shank D=12mm B=10mm L=25mm

Sleeve enlarger for shank D=12mm B=10mm L=25mm

  • D=12 d=10mm
€9.30
€11.25 VAT incl.
Code:799.100.00
In stock
Sleeve enlarger for shank D=16mm B=13mm L=45mm

Sleeve enlarger for shank D=16mm B=13mm L=45mm

  • D=16 d=13mm
€12.40
€15.00 VAT incl.
Code:799.130.00
In stock
Sleeve enlarger for shank D=9,5mm B=6mm L=25mm

Sleeve enlarger for shank D=9,5mm B=6mm L=25mm

  • D=9,5 d=6mm
€12.40
€15.00 VAT incl.
Code:799.160.00
In stock
Sleeve enlarger for shank D=9,5mm B=6,35mm L=25mm

Sleeve enlarger for shank D=9,5mm B=6,35mm L=25mm

  • D=9,5 d=6,35mm
€12.40
€15.00 VAT incl.
Code:799.164.00
In stock
Sleeve enlarger for shank D=9,5mm B=8mm L=25mm

Sleeve enlarger for shank D=9,5mm B=8mm L=25mm

  • D=9,5 d=8mm
€12.40
€15.00 VAT incl.
Code:799.180.00
In stock
Sleeve enlarger for shank D=12mm B=6mm L=25mm

Sleeve enlarger for shank D=12mm B=6mm L=25mm

  • D=12 d=6mm
€9.30
€11.25 VAT incl.
Code:799.260.00
In stock
Sleeve enlarger for shank D=12,7mm B=6,35mm L=25mm

Sleeve enlarger for shank D=12,7mm B=6,35mm L=25mm

  • D=12,7 d=6,35mm
€10.10
€12.22 VAT incl.
Code:799.264.00
In stock
Sleeve enlarger for shank D=10mm B=8mm L=25mm

Sleeve enlarger for shank D=10mm B=8mm L=25mm

  • D=10 d=8mm
€9.30
€11.25 VAT incl.
Code:799.280.00
In stock
Sleeve enlarger for shank D=12mm B=8mm L=25mm

Sleeve enlarger for shank D=12mm B=8mm L=25mm

  • D=12 d=8mm
€9.30
€11.25 VAT incl.
Code:799.380.00
In stock
Sleeve enlarger for shank D=12,7mm B=8mm L=25mm

Sleeve enlarger for shank D=12,7mm B=8mm L=25mm

  • D=12,7 d=8mm
€10.10
€12.22 VAT incl.
Code:799.480.00
In stock
Oversized bush for ball bearing D=19,05mm L=12mm d=12,7mm

Oversized bush for ball bearing D=19,05mm L=12mm d=12,7mm

  • D=12 d=8mm
  • L=25mm
€8.80
€10.65 VAT incl.
Code:799.503.00
In stock
Oversized bush for ball bearing D=50,8mm L=12mm d=12,7mm

Oversized bush for ball bearing D=50,8mm L=12mm d=12,7mm

  • D=19,05 d=12,7mm
€12.10
€14.64 VAT incl.
Code:799.517.00
In stock
About this category

Reducing sleeves for router shanks and ball bearings

A reducing sleeve adapts a smaller diameter to a larger size. In this category you will find CMT reducing sleeves in two types: sleeves for the shank, which you slide over the shank of a router bit so it fits a larger collet, and sleeves for ball bearings, which let you mount a bearing with a larger bore on a thinner axle. The inside diameters range from 4,76 to 13 mm; the outside diameters match common collet sizes such as 8, 9,5, 12 and 12,7 mm.

Reducing sleeve for the shank: choose based on shank and collet

The inner diameter of the sleeve must be exactly the same as the shank of your router bit, the outer diameter the same as the size of your collet. This allows a router bit with a shank of 6, 6,35 or 8 mm to still fit in a larger collet. The shank sleeves are usually 25 mm long: slide the sleeve fully over the shank and clamp sleeve and shank together as deeply as possible in the collet, without letting the shank rest on the bottom. If there is a suitable collet for your shank, that remains the preferred option; see the collet holders.

Reducing sleeve for ball bearings

With routers fitted with a guide bearing, you can use a reducing sleeve to mount a ball bearing with a larger bore on the router's axle, for example on an axle of 4,76 mm (3/16 inch). This lets you use a bearing with a different outside diameter with the same router and changes the cutting depth. Fit sleeve and bearing cleanly and without play, tighten the assembly securely and check by hand that the bearing turns freely. Loose ball bearings can be found in the corresponding category.

What is the difference between a reducing sleeve and a reducing ring?
A reducing ring reduces an oversized bore, for example on a saw blade or cutter head that has to fit on a thinner axle. A reducing sleeve does the opposite for a shank or axle: it adapts a small diameter to a larger size, so it fits in the collet or in the bearing.
Is a router bit with a reducing sleeve just as accurate as in the correct collet?
Direct clamping in the correctly sized collet remains the best choice, because every extra layer in the clamping chain can cause a slight deviation. A clean, well-fitting reducing sleeve is a solid alternative when no collet in the size of your shank exists for your machine.
How do I measure which reducing sleeve I need?
Use a caliper to measure the diameter of the shank or axle, and the size of the collet or the bore of the bearing. Note imperial sizes: 6,35 mm is 1/4 inch and 12,7 mm is 1/2 inch, and these differ just little enough from 6 and 12 mm that you cannot tell by eye.
What should I pay attention to when mounting?
Fit the sleeve cleanly and free of grease, without burrs, and make sure the shank or axle fits without play, because play causes imbalance at high speeds. After clamping, let the machine run briefly at low speed first and check that everything rotates without vibration.
Compiled by Garnotec’s specialist team — specialist in professional cutting tools for more than 30 years. Unsure which version suits your machine or material? Contact our team · View the full range

We use cookies to ensure the website functions properly. In addition, we place analytical cookies (Google Analytics, Microsoft Clarity) to analyse the use of the website. These are only placed after your consent. More information