Collets
The connection between machine and cutter depends on the collet. It determines the tool's concentricity and thus the quality of every cut. This range includes precision collets in the common ER systems — ER20, ER25 and ER32 — as well as versions according to DIN 6388 and collets for specific collet chucks.
A collet is a wear part, even if it seems indestructible. Fatigued slots clamp unevenly, causing the cutter no longer to run centred and creating vibrations. You will see this in the milling pattern and the tool life. Clean the collet and taper with every tool change, never clamp on too short a shank, and replace the collet when there is visible wear or vibration. Always choose the size exactly according to the shank diameter: a collet can clamp only to a limited extent below its nominal size.
What is the shank diameter of the tool to be clamped?
Filters
Availability
L (total length) in mm
D3 (diameter 3)
Collet system
D (diameter) in mm

Precision collet ER20 · 184.080.20
- ER20 L=31 mm
- D³=8 mm D=21 mm

Precision collet ER25 · 184.080.25
- ER25 L=35 mm
- D³=8 mm D=26 mm

Precision collet ER40 · 184.082.00
- ER40 L=46 mm
- D³=8 mm D=41 mm

Precision collet ER40 (high precision) · 184.082.00H
- ER40 precision collet (0,005) L=46 mm
- D³=8 mm D=41 mm

Precision ER32 collet · 184.090.00
- ER32 L=40 mm
- D³=9 mm D=33 mm

Precision collet chuck ER16 · 184.090.16
- ER16 L=27,5 mm
- D³=9 mm D=17 mm

Precision collet ER20 · 184.090.20
- ER20 L=31 mm
- D³=9 mm D=21 mm

Precision collet ER25 · 184.090.25
- ER25 L=35 mm
- D³=9 mm D=26 mm

Precision ER32 collet · 184.095.00
- ER32 L=40 mm
- D³=9,52 mm D=33 mm

Precision collet ER40 · 184.096.00
- ER40 L=46 mm
- D³=9,52 mm D=41 mm

Precision ER32 collet · 184.100.00
- ER32 L=40 mm
- D³=10 mm D=33 mm

Precision collet ER32 (high precision) · 184.100.00H
- ER32 precision collet (0,005) L=40 mm
- D³=10 mm D=33 mm

Precision collet chuck ER16 · 184.100.16
- ER16 L=27,5 mm
- D³=10 mm D=17 mm

Precision collet ER20 · 184.100.20
- ER20 L=31 mm
- D³=10 mm D=21 mm

Precision collet ER25 · 184.100.25
- ER25 L=35 mm
- D³=10 mm D=26 mm

Precision collet ER40 · 184.102.00
- ER40 L=46 mm
- D³=10 mm D=41 mm

Precision ER32 collet · 184.110.00
- ER32 L=40 mm
- D³=11 mm D=33 mm

Precision collet ER20 · 184.110.20
- ER20 L=31 mm
- D³=11 mm D=21 mm

Precision ER32 collet · 184.120.00
- ER32 L=40 mm
- D³=12 mm D=33 mm

Precision collet ER32 (high precision) · 184.120.00H
- ER32 precision collet (0.005) L=40 mm
- D³=12 mm D=33 mm

Precision collet ER20 · 184.120.20
- ER20 L=31 mm
- D³=12 mm D=21 mm

Precision collet ER25 · 184.120.25
- ER25 L=35 mm
- D³=12 mm D=26 mm

Precision collet ER40 · 184.122.00
- ER40 L=46 mm
- D³=12 mm D=41 mm

Precision collet ER40 (high precision) · 184.122.00H
- ER40 precision collet (0,005) L=46 mm
- D³=12 mm D=41 mm
24 of 120 products shown
ER11 to ER40 collets and DIN 6388 for CNC
The collet clamps the shank of your cutter or drill in the holder and thus helps determine concentricity, vibration and tool life. Here you will find precision collets from CMT in the ER11, ER16, ER20, ER25, ER32 and ER40 systems and according to DIN 6388 (EOC16 and EOC25), for shanks from 1 to 25 mm, including inch sizes such as 1/4, 3/8, 1/2 and 3/4 inch.
First the right system, then the right size
A collet only fits into a holder of the same system: an ER32 collet belongs in an ER32 holder, an EOC25 collet in a DIN 6388 holder. ER and DIN 6388 are not interchangeable. Then choose the size exactly according to the shank diameter. An ER collet can clamp slightly below its nominal size, but for routers the exact size gives the best concentricity and the highest clamping force. So a 6 mm shank belongs in a 6 mm collet, not in an 8 mm one.
Clean and clamp to a sufficient depth
Blow out the collet, the taper of the holder and the clamping nut at every tool change: resin buildup and chips cause runout immediately. Clamp the shank over at least two thirds of the collet length and always on the cylindrical part. With ER collets, first click the collet into the clamping nut and only then screw the nut onto the holder. Tighten with the appropriate hook spanner, preferably outside the machine. You will find clamping nuts and hook spanners under parts for CNC tool holders and CNC accessories.