Cutting tools: choice of 20,000 articles
Select language

CNC saw blade holder

For cutting grooves, separating panels or making angled cuts directly on the CNC machine, fit a saw blade in a CNC saw blade holder. These precision holders are available with an HSK-F63 shank for modern machining centres and with a cylindrical shank for spindles with collet chuck mounting, and clamp the blade exactly square and concentric on the spindle.

A saw blade on a CNC spindle places higher demands than a cutter: the large diameter amplifies any imbalance. Therefore, at every blade change, check the contact surfaces of flange and blade for chips and resin residue, and tighten the fixing according to the instructions. This keeps the cut clean and prevents vibrations that affect both the cut quality and the spindle bearings. With the right holder, your CNC becomes a fully-fledged sawing station.

Read more about this category
Precision saw holder with cylindrical shank D=59mm S=20mm

Precision saw holder with cylindrical shank D=59mm S=20mm

  • Collet system:
  • Connection type: 20 mm
  • Direction of rotation: Right and left
€89.00
€107.69 VAT incl.
Code:183.410.30
In stock
Precision saw holder with HSK-F63 shank D=59mm L=78mm

Precision saw holder with HSK-F63 shank D=59mm L=78mm

  • Clamping system:
  • Connection type: HSK-F63
  • Rotation direction: Right and left
€148.00
€179.08 VAT incl.
Code:183.420.30
In stock
Precision saw holder with HSK-F63 shank D=98mm L=102mm

Precision saw holder with HSK-F63 shank D=98mm L=102mm

  • Clamping system:
  • Connection type: HSK-F63
  • Rotation direction: Right and left
€344.00
€416.24 VAT incl.
Code:183.421.30
In stock
Precision saw holder with HSK-F63 shank D=110mm L=40mm

Precision saw holder with HSK-F63 shank D=110mm L=40mm

  • Clamping system:
  • Connection type: HSK-F63
  • Rotation direction: Right and left
€277.20
€335.41 VAT incl.
Code:183.422.30
In stock
About this category

CNC saw blade holders with HSK-F63 or cylindrical shank

With a saw blade holder, you use a circular saw blade on your CNC machining centre instead of a milling cutter, for example to saw grooves, separate panels or make straight cuts. Here you will find precision saw blade holders from CMT with HSK-F63 shank for saw blades up to Ø 250, 300 or 350 mm, and a version with a 20 mm cylindrical shank for collet chucks. All holders accept saw blades with a 30 mm arbor hole and are suitable for right- and left-hand rotation.

Sawing instead of milling on the CNC

For straight through cuts in sheet material, a saw blade is often more efficient than a milling cutter: it cuts a narrow kerf with low chip volume and a high feed rate. The holder determines the maximum blade diameter and therefore the cutting depth: choose the 59, 98 or 110 mm flange depending on whether you want to use blades up to Ø 250, 300 or 350 mm. Check that limit against the thickest board you process, and take into account the space around the spindle of your machine.

Arbor hole, flanges and speed

The saw blade must fit the holder exactly with its 30 mm arbor hole; also check whether the drive holes of the blade match those of the holder (4/M6/48 or 6/M6/80). In addition, make sure that the blade's maximum speed is higher than the spindle speed — at CNC speeds, that is no mere formality. Keep the flanges completely clean: one chip between flange and blade causes runout and thus a wavy cut edge.

Why saw on a CNC instead of milling?
For straight through cuts in sheet material, a saw blade is often faster: a narrow kerf, less chip volume and higher feed. In addition, you save your milling cutters for the work they are meant for.
Which blade diameter can I use?
That is determined by the holder: with the HSK-F63 holders, you can use blades up to Ø 250, 300 or 350 mm, depending on the flange diameter. Also check what your machine allows and work back from the cutting depth you need for your thickest board.
Do I need to pay attention to the blade's maximum speed?
Absolutely. The blade's maximum speed must be higher than the spindle speed; at CNC speeds, that is no mere formality. Check the specification on the blade before mounting it.
Why is my cut edge wavy?
Most often due to runout: a chip between flange and blade, a damaged flange or a blade that does not sit without play on the holder. Clean everything and check whether the blade runs perfectly true before continuing to saw.
HSK-F63 or cylindrical shank?
The HSK-F63 holder is intended for machining centres with an HSK-F63 spindle and automatic tool change. The holder with a 20 mm cylindrical shank is clamped in a collet chuck, for example on a machine without HSK. Choose the version that matches the spindle of your machine.
Compiled by Garnotec’s specialist team — specialist in professional cutting tools for more than 30 years. Unsure which version suits your machine or material? Contact our team · View the full range

We use cookies to ensure the website functions properly. In addition, we place analytical cookies (Google Analytics, Microsoft Clarity) to analyse the use of the website. These are only placed after your consent. More information