FastX4 – quick-change system
With the FastX4 quick-change system, you can change hole saws without removing the holder from the drill: the hole saw clicks onto the change holder and locks into place immediately. This system saves an enormous amount of time on job sites where you drill various diameters one after another. Whether you are drilling pipe penetrations or installing spotlights, a change never takes long.
This category groups the holders and accessories for the system: change holders in short versions of 160 and 180 mm and extra-long versions of 320 mm, each available with a centring drill in HSS or carbide (HW). Choose the long holder when you are working through thicker packs or in hard-to-reach places, and the carbide centring drill as soon as abrasive sheet material or hard wood species are involved — it has a significantly longer service life.
Filters
D (diameter) in mm
Cutting material
Type
Drill shank
L (total length) in mm
S (shank) special
Material to be machined

Centering tool for enlarging holes S=Hexagonal L=155mm
- One hole saw from 19-30mm and one hole saw of 32mm or larger fits on the holder

300mm extension for interchangeable holder · 550.EX2
- Suitable for holder 550.HS2 550.HW2 and 551.HS2
- Not suitable for 550.HS2XL 550-HW2XL and 551-HS2XL

Quick-change holder short 180mm, HSS pilot drill · 550.HS1
- Suitable for hole saws type 550 with diameter 14 - 30mm
- Shank diameter 7,8mm hexagonal
- Multiconstruct, Wood, Plastic, Plasterboard …

Quick-change holder short 180mm, HSS pilot drill · 550.HS2
- Suitable for hole saws type 550 with diameters 32 - 330mm
- Shank diameter 9,8mm hexagonal
- Multiconstruct, Wood, Plastic, Plasterboard …

Extra-long quick-change holder, HSS centre drill L=320mm
- Suitable for hole saws type 550 from diameter 32 - 330mm
- Shank diameter 13mm hexagonal
- Multiconstruction, Wood, Plastic, Plasterboard …

Short interchangeable holder 180mm, HW centering drill · 550.HW1
- Suitable for hole saws type 550 with diameter 14 - 30mm
- Shank diameter 7,8mm hexagonal
- Brick, Ceramic, Plasterboard, Aerated concrete …

Short interchangeable holder 180mm, HW centering drill · 550.HW2
- Suitable for hole saws type 550 with diameter 32 - 330mm
- Shank diameter 9,8mm hexagonal
- Brick, Ceramic, Plasterboard, Aerated concrete …

Replaceable holder extra long, HW centre drill S=Hexagonal L=320mm
- Suitable for hole saws type 550 with diameter 32 - 330mm
- Shank diameter 13mm hexagonal
- Brick, Ceramic, Plasterboard, Aerated concrete …

Transition connector from SDS to HEX10 S=SDS L=95mm
- Suitable for holder 550.HS1 550.HW1 551.HS1 and 552.DD1
- Not suitable for 550.HS2XL 550-HW2XL 550.EX1 550.EX2 and 551-HS2XL

SDS to HEX13 adapter S=SDS L=95mm
- Suitable for holder 550.HS2 550.HW2 550.DB1 551.HS2 and 552.DD2
- Not suitable for 550.HS2XL 550-HW2XL 550.EX1 550.EX2 and 551-HS2XL

Short quick-change holder 160mm, HSS centre drill · 551.HS1
- Suitable for hole saws type 551 with diameter 14 - 30mm
- Shank diameter 7,8mm hexagonal
- Stainless steel, Aluminium, Zinc, Copper …

Short quick-change holder 160mm, HSS centre drill · 551.HS2
- Suitable for hole saws type 551 with diameters 32 - 330mm
- Shank diameter 9,8mm hexagonal
- Stainless steel, Aluminium, Zinc, Copper …

Extra-long quick-change holder 320mm, HSS centre drill L=330mm
- Suitable for hole saws type 551 with a diameter 32 - 330mm
- Shank diameter 13mm hexagonal
- Stainless steel, aluminium, zinc, copper …

Interchangeable holder 143mm, centering drill DP D=8mm
- Suitable for hole saws type 552 with diameter 14 - 30mm
- Hard stone, Granite, Gres tiles …

Interchangeable holder 143mm, centering drill DP D=10mm
- Suitable for hole saws type 552 with diameter 32 - 330mm
- Hard stone, Granite, Gres tiles …
FastX4 quick-change system: arbor holders and pilot drills for hole saws
CMT’s FastX4 quick-change system revolves around the arbor holder: it stays in the drill while you change hole saws. In this category you will find short arbor holders of 160 and 180 mm and extra-long holders of 320 mm with an HSS pilot drill — the 180 and 320 mm also with carbide (HW) pilot drill —, a 143 mm arbor holder with diamond pilot drill (DP), a 300 mm extension, adapter connections from SDS to HEX10 and HEX13 and a centering piece to enlarge existing holes.
Which arbor holder and pilot drill should you choose?
The length of the holder determines how far you can reach. A short 160 or 180 mm arbor holder is most practical on the workbench and in cabinet carcasses; the extra-long 320 mm holder or the 300 mm extension is used when the hole is far from the machine or difficult to reach. An HSS pilot drill is sufficient for most applications; choose carbide (HW) when abrasive sheet material or hardwood quickly dulls the tip. The holder with DP pilot drill is intended for the diamond hole saws in series 552.
SDS adapter and enlarging existing holes
The arbor holders have a hex shank. If you work with a hammer drill with SDS chuck, you place an adapter from SDS to HEX10 or HEX13 in between and use the machine only in drilling mode, without hammer action. If an existing hole needs to be enlarged, the centering piece guides the hole saw into the existing hole, even where the pilot drill no longer has a hold. This way you can fully equip the hard metal hole saws 550 and the bi-metal hole saws 551.