Dowel drill bit – System (Festool)
Festool's Domino dowel system works with its own router bits. This category brings together special dowel drills for Festool Domino, specifically matched to the collet and oscillating movement of the Domino machine. This preserves the original machining quality, combined with the sharpness and service life of CMT tools.
All versions in this range are right-hand cutting, as driven by the Festool Domino machine. Because the drill rotates and moves back and forth during routing, the cutting edges are subjected to greater stress than with classic dowel drills. You can quickly recognise a drill that is starting to dull by ragged slot walls and a machine that has to work harder. Replace it in time: a sharp Domino drill directly determines the fit of the joint.
What diameter should the borehole be?
Filters
D (diameter) in mm
Cutting material
I (effective cutting length) in mm
L1 (length 1) in mm
S (shank) special
L (total length) in mm

Special dowel drill for Festool - Domino, right-hand D=4mm L=38mm L1=27mm I=11mm
- I=11mm LT=38mm
- S=M6x0,75x27mm Z2
- RH (right-hand rotation) HWM

Special dowel drill for Festool - Domino, right-hand D=5mm L=49mm L1=29mm I=20mm
- I=20mm LT=49mm
- S=M6x0,75x29mm Z2
- RH (right-hand rotation) HW

Special dowel drill for Festool - Domino, right-hand D=6mm L=49mm L1=21mm I=28mm
- I=28mm LT=49mm
- S=M6x0,75x21mm Z2
- RH (right-hand rotation) HW

Special dowel drill for Festool - Domino, right-hand D=8mm L=49mm L1=21mm I=28mm
- I=28mm LT=49mm
- S=M6x0,75x21mm Z2
- RH (right-hand) HW

Special dowel drill for Festool - Domino, right-hand D=8mm L=90mm L1=40mm I=50mm
- I=50mm LT=90mm
- S=M8x1x40mm Z2
- RH (right-hand rotation) HW

Special dowel drill for Festool - Domino, right-hand D=10mm L=49mm L1=21mm I=28mm
- I=28mm LT=49mm
- S=M6x0,75x21mm Z2
- RH (right-hand rotation) carbide

Special dowel drill for Festool - Domino, right-hand D=10mm L=90mm L1=20mm I=70mm
- I=70mm LT=90mm
- S=M8x1x20mm Z2
- RH (right-hand rotation) HW

Special dowel drill for Festool - Domino, right-hand D=12mm L=90mm L1=20mm I=70mm
- I=70mm LT=90mm
- S=M8x1x20mm Z2
- RH (right-hand rotation) HW

Special dowel drill for Festool - Domino, right-hand D=14mm L=90mm L1=20mm I=70mm
- I=70mm LT=90mm
- S=M8x1x20mm Z2
- RH (right-hand rotation) HW
Domino cutters for Festool DF 500 and DF 700
These special dowel drills are Domino cutters for Festool Domino machines. Unlike a conventional dowel drill, such a cutter does not bore a round hole: while rotating, the machine makes it oscillate sideways, creating an elongated slot for a flat Domino tenon. The cutters rotate clockwise and are screwed onto the machine with their internal thread: M6 x 0,75 for the DF 500, M8 x 1 for the DF 700.
Which cutter for which machine?
For the DF 500, cutters are available in 4, 5, 6, 8 and 10 mm, and for the DF 700 in 8, 10, 12 and 14 mm. The cutter diameter corresponds to the thickness of the Domino tenon you use; the tenon length determines the cutting depth you set on the machine. A 8 or 10 mm cutter therefore exists in two versions, with the thread and length of the DF 500 or of the DF 700. Always check the machine type before ordering.
Sharp cutter, tight joint
Because the cutter rotates and oscillates at the same time, the cutting edges are subjected to heavier loads than with ordinary dowel drilling. You can recognize a blunt cutter by ragged slot walls, scorch marks and a machine that has to work harder; the slot will also be wider and the tenon will sit looser. Regularly remove resin from the cutter, screw it fully onto a clean thread when changing it, and replace it in time.
What is a Domino cutter?
Does a DF 500 cutter fit the DF 700?
Which diameter matches which Domino tenon?
Why is my Domino joint looser than expected?
Related categories
- Hole saws
- Dowel drill bit – Standard (with clamping flat)
- Dowel drill – Through drill (with flat)
- Diamond drills
- Speed drills
- Dowel drill bit – System (Mafell)
- Slot drills
- Forstner Bits
- Rosette Cutters
- Dowel drill – threaded shank
- Countersinks
- Plug cutters
- Cylindrical head drills
- Industrial lock mortising cutters
- Fish-mouth drills
- Spiral drills
- Square mortise bits