Cutting tools: choice of 20,000 articles
Select language

Fish-tail drills – threaded shank

Some mortising machines do not accept their tooling via a chuck, but via a threaded mount. For that purpose there is the fish-tail drill with threaded shank. The drill is screwed directly onto the drive, creating a secure connection that cannot slip under sideways cutting loads. The range includes not only a classic right-hand fish-tail drill, but also mortising cutters with diameters from 10 to 16 mm.

Choose the diameter according to the width of the mortises you make most often. With a 16 mm cutter, you can machine wide mortises faster, while 10 or 12 mm leaves more reserve to stay exactly on the marking. Screw the drill onto the thread hand-tight and carefully: the cutting direction pulls the drill tighter on its own during operation.

Read more about this category
Find what you need faster
Step 1 of 1
Lock housing cutter D=10, right L=100mm
Wood-related applications

Lock housing cutter D=10, right L=100mm

  • D=10mm
  • LT=100mm
  • S=M12x1 Z2
€39.00
€47.19 VAT incl.
Code:163.100.11
In stock
Lock housing cutter D=12, right-hand L=100mm
Wood-related applications

Lock housing cutter D=12, right-hand L=100mm

  • D=12mm
  • LT=100mm
  • S=M12x1 Z2
€72.20
€87.36 VAT incl.
Code:163.120.11
In stock
Lock mortising cutter D=14, right-hand D=14mm S=M12x1
Wood-related applications

Lock mortising cutter D=14, right-hand D=14mm S=M12x1

  • LT=100mm
  • S=M12x1 Z2
  • RH (right-hand rotation) HW
€74.60
€90.27 VAT incl.
Code:163.140.11
In stock
Lock case cutter D=16, right-hand D=16mm S=M12x1
Wood-related applications

Lock case cutter D=16, right-hand D=16mm S=M12x1

  • LT=100mm
  • S=M12x1 Z2
  • RH (right-hand rotation) HW
€79.50
€96.20 VAT incl.
Code:163.160.11
In stock
Fish-tail drill bit, right D=18mm L=105mm · 163.180.11
Wood-related applications

Fish-tail drill bit, right D=18mm L=105mm · 163.180.11

  • LT=105mm
  • S=M12x1 Z2
  • RH (right-hand rotation) HW
€68.30
€82.64 VAT incl.
Code:163.180.11
In stock
Fish-tail drill bit, right D=18mm L=105mm · 163.180.31
Wood-related applications

Fish-tail drill bit, right D=18mm L=105mm · 163.180.31

  • LT=105mm
  • S=M12x1 Z2
  • RH (right-hand rotation) SP
Code:163.180.31
About this category

Bore bits and mortise box cutters with threaded shank

Some mortising machines do not hold the tool in a drill chuck, but by means of a thread. These bore bits and mortise box cutters with M12x1 threaded shank are intended for that purpose. You screw them directly onto the drive, which gives a solid connection that cannot slip when the cutter is subjected to lateral load. They rotate to the right, usually with carbide cutting edges, in diameters from 10 to 18 mm.

Diameter according to the mortise box

Choose the diameter according to the width of the mortises you make most often. With a 16 or 18 mm cutter, you can machine wide mortises faster; with 10 or 12 mm, you keep more reserve to stay exactly on the marking. Cut in depth passes of a few millimetres and let the cutter remove only a limited width per pass, so that the chip is carried away smoothly and the cutter does not start to vibrate.

Thread and mounting

Before ordering, check whether the drive of your machine has an M12x1 thread. Tighten the cutter by hand onto a clean thread: sawdust or chips in the thread prevent it from seating fully, and then it will not run true. Because all cutters rotate to the right, the cutting direction pulls the cutter tighter during operation; so never use force when tightening.

Does this bit fit in a standard drill?
No. The M12x1 threaded shank is meant for a mortising machine with threaded holder and does not fit in a drill chuck. For a machine with drill chuck or collet chuck, choose the bore bits with cylindrical shank, which serve the same purpose.
What thread do these cutters have?
All cutters in this category have an M12x1 thread and are right-hand rotating. Compare them with the tool currently fitted to the machine or with the machine documentation to check whether it matches. A different thread will not screw on fully and will damage the drive.
Why is my mortise wider than the cutter?
Usually because the cutter does not seat fully on the thread and therefore runs out of true, or because it is dull. Clean the thread, screw the cutter on fully and check the runout on a test piece.
Can I have these cutters resharpened?
Carbide cutters can often be resharpened, provided the shape and diameter are maintained exactly. Through our sharpening and modification service, you can have them resharpened so that a cutter lasts longer under intensive use.
Compiled by Garnotec’s specialist team — specialist in professional cutting tools for more than 30 years. Unsure which version suits your machine or material? Contact our team · View the full range

We use cookies to ensure the website functions properly. In addition, we place analytical cookies (Google Analytics, Microsoft Clarity) to analyse the use of the website. These are only placed after your consent. More information