Jigsaw blades
The right jigsaw blade determines whether a curve is cut cleanly and a cut remains splinter-free. In this category you will find jigsaw blades for every machine with a T-shank — sorted by what you want to saw. The naming guides you: fine straight for splinter-free straight cuts in sheet material and veneer, coarse straight for fast sawing in thick wood (up to 180 mm length), and curve straight for tight curves. Each version is available in several lengths (76 to 185 mm) — choose a blade that extends well beyond your material thickness so the teeth can cut freely. Saw melamine-faced board with the good side facing down, or choose a down-cut blade — then the visible side stays neat.
Which material are you looking for a solution for?
Filters
Cutting material
I (effective cutting length) in mm
Machining type
L (total length) in mm
B (tooth shape)
Material group
Material to be machined
Packaging unit

Jigsaw blade (Straight curve) L=100mm I=75mm
- TS=4 TPI=6 TPI
- HCS , Wood
- 5 ~ 60mm

Jigsaw blade 116mm (Fine straight) 3
- L=116mm I=90mm
- TS=3 TPI=8 TPI
- HCS , Wood & Plastic

Jigsaw blade 120mm (Fine straight) L=116mm I=95mm
- L=120 I=95
- T= 1,27-2 TPI= 13 TPI

Jigsaw blade 152mm L=150mm I=100mm
- L=152mm I=100mm
- TPI
- soft material non-abrasive

jigsaw blade (fine straight) L=132mm I=100mm
- TS=1,7 - 2,6 TPI=10 - 15 TPI
- Bim 8% Co , Wood & Metal
- Laminate (<60mm), Sheet steel (3-18mm), Glass fibre reinforced plastic (<60mm)

Jigsaw blade 132mm (Coarse straight) I=110mm 4,3
- L=132mm I=110mm
- TS=4,3mm TPI=6 TPI
- HM , Special

Jigsaw blade 132mm (Coarse straight) I=110mm 4
- L=132mm I=110mm
- TS=4 TPI=6 TPI
- HCS , Wood

Jigsaw blade 132mm (Coarse straight) I=105mm 3.5-5
- L=132mm I=105mm
- TS=3,5-5mm TPI=5-7 TPI
- HM , Special

Jigsaw blade (fine straight) L=185mm I=160mm
- TS=1,8 TPI=14 TPI
- Bim 8% Co , Metal
- <120mm

Jigsaw blade (Coarse straight) L=180mm I=155mm
- TS=4 TPI=6 TPI
- HCS , Wood
- 5 ~ 135mm
10 of 34 products shown
Jigsaw blades for wood, metal and sheet materials
The jigsaw blade determines whether you get a clean cut or a torn edge. Tooth pitch, tooth shape and blade material must match what you are cutting. Here you will find CMT jigsaw blades with T-shank from 76 to 185 mm long, for softwood and hardwood, plywood, OSB, plastic, sheet steel and profiles, and for special materials such as drywall, fiber cement and fiberglass-reinforced plastic — in HCS, HSS, bi-metal with 8% cobalt and carbide.
Which blade for which material?
For fast cutting in construction timber and thick sheet materials, choose a coarse, set tooth pattern with a low TPI, for example 6 teeth per inch; for fine, splinter-free cuts in plywood and sheet materials, choose a ground blade with a finer tooth pitch. Cut melamine-faced panels and worktops with the visible side facing down: the teeth cut on the upstroke, so the top side mainly splinters. For sheet steel and profiles, use a bi-metal or HSS blade with a fine pitch and at least three teeth in the wall thickness; for drywall, fiber cement or ceramic, a carbide or HW grit blade.
Curved cuts and orbital action
A narrow blade follows a small radius, a wide blade cuts straighter. Turn the orbital action off for curves, thin material and visible surfaces; set it higher for fast straight cuts in thick wood. Cut with moderate feed pressure: if you push too hard, the blade bends away and the cut becomes skewed — a blade that runs out on the underside is almost always pushed through too hard.
Which jigsaw blade do I use for laminate or a worktop?
Does every saw blade fit my jigsaw?
Why does my jigsaw cut crooked?
Which blade do I take for metal?
Need help choosing?
In our guide, you can read about the differences and which choice suits your work.